One hour and 35 minutes is about 1.58 decimal hours. It is not 1.35 hours. That small notation difference can make a personal overtime total look wrong even when the start and end times are right.
For police officers moving between a duty notebook, an overtime slip and a timekeeping screen, the first question is simple: what unit does this number represent? A clock reading, a duration and a decimal-hour value need different treatment.
This guide explains the arithmetic with ordinary-day examples. It does not decide which time is compensable, what rate applies, or which rounding, break or minimum-credit rules your agency uses.
Clock time, hours and minutes, and decimal hours
Consider three entries that might appear in the same workflow:
- 15:40 as a clock reading: 3:40 p.m. on a 24-hour clock. It tells you when something happened.
- 1 h 35 min as a duration: a period lasting 95 minutes. It tells you how long something took.
- 1.35 h as decimal hours: one hour plus 0.35 of an hour, or 1 hour and 21 minutes.
A colon alone can also be ambiguous: “1:35” might mean a clock reading or a duration depending on the field. Label a handwritten total as “1 h 35 min” or “95 min” so the next person does not have to infer your meaning.
Convert minutes to decimal hours by dividing by 60
An hour contains 60 minutes, not 100. NIST’s Guide to the SI, Table 6 provides that unit relationship. The conversion follows directly:
Decimal hours = whole hours + (remaining minutes ÷ 60).
- 15 minutes = 0.25 h.
- 30 minutes = 0.50 h.
- 45 minutes = 0.75 h.
- 1 hour 35 minutes = 1 + 35 ÷ 60 = 1.58333… h.
Written to two decimal places, the last example is approximately 1.58 h. That is a mathematical example, not an instruction to round an agency entry to hundredths. Use the precision and conversion method required by the system receiving the record.
A worked example: 16:10 to 17:45
Suppose a documented period starts at 16:10 and ends at 17:45 on the same ordinary day, with no clock or time-zone change. First count the elapsed minutes:
- 16:10 to 17:10: 60 minutes.
- 17:10 to 17:45: 35 minutes.
- Total: 95 minutes, or 1 hour 35 minutes.
If you need a decimal-hour cross-check, divide 95 by 60: 1.58333… h. Do not type “1.35” into a decimal-hours field merely because the original duration was written as “1:35.”
Now reverse the check. A decimal entry of 1.35 h represents 81 minutes because 1.35 × 60 = 81. The 14-minute difference comes from notation, not from an unexplained change to the original clock readings.
Add minutes before comparing your personal total
For an independent arithmetic check, keep the original minute totals available. Suppose you have one period of 95 minutes and another of 50 minutes:
95 + 50 = 145 minutes = 2 hours 25 minutes = 2.41666… decimal hours.
Adding the labels “1.35” and “0.50” as ordinary decimals would instead produce 1.85 h, which represents 111 minutes. That is a different duration. Likewise, separately rounding converted values can produce a different sum from converting the combined raw minutes.
Keep the raw-duration check separate from the official submission. If the agency rounds each line, uses approved increments or applies another authorized method, reconcile against that method rather than changing the official entries to force your personal total to match.
Military time does not make the duration decimal
A tour from 07:05 to 15:40 spans 8 hours 35 minutes in an ordinary same-day clock calculation. Expressed as decimal hours, that is 515 ÷ 60, or approximately 8.58333 h. “15:40” is an end time; “8 h 35 min” is the resulting duration.
Total tour duration is not automatically payable overtime. It does not, by itself, establish a break deduction, approval, premium or pay entitlement. For overnight work, retain the relevant dates. If a tour crosses a daylight-saving or time-zone change, preserve the applicable offsets and check the actual elapsed interval; two clock readings alone may not describe it fully.
Use the right NinetySix tool for the question
Open Overtime Recorder / Tour Time →
NinetySix’s Tour Time Calculator checks start-to-end-of-tour time in 24-hour or AM/PM notation, including overnight tours. Calculator-only checks do not save an overtime entry and do not deduct breaks. Use Overtime Recorder when you want to capture an overtime slip or enter a personal record, then return to the saved entries in your dashboard.
The RDO Calendar answers a separate planning question: which dates are workdays or days off? A planned tour, an elapsed-time calculation and an approved overtime entry should remain identifiable as different records.
Before choosing a plan, check the current Officer Pro benefits and prices. Saved overtime is a paid feature. Eligible new accounts can try one testimony draft with no card required; that testimony allowance does not include saved overtime records or paid violation-code search.
A quick check before you submit
Keep the original start and end times, relevant dates, total minutes and required submission unit together. Confirm which items were approved and which remain personal notes. The Department of Labor’s recordkeeping overview distinguishes daily and weekly hours from wage and payment records; a personal calculator is not a substitute for the employer’s records or applicable rules.
If a total differs, identify the exact entry and unit before raising it through your agency’s correction process. “95 minutes, shown as 1.58333… hours before the required conversion” is easier to investigate than an unlabeled “1.35.”
